2022.08.09 PC frequency control by protocol rs 485
127 USD1) PC frequency control by protocol rs 485 Modbus RTU with PR, according to the logic, 2 modes: manual, automatic
2) programmed rally: OMRON, Lovato, Schneider Electric, Simens
3) PC: Lenze ESV223N04TXB (22kW), now Ylmaz NZ2400-22G/30P
Conditions of:
1) On the basis of the existing scheme to develop the scheme on the basis of the programmed relay to implement the control of the twist frequency of the engine 22 kW from its current (A).2) Connect with the frequency converter to be implemented by Modbus protocol (RS-485).3) The scheme must be implemented for two working modes: manual and automatic.4) The launch of the oil press takes place with the participation of the operator and then the manual switch is transferred to the automatic mode.5) Work in the automatic mode requires the following algorithm:
The criterion of the necessary load of the engine is its nominal current (nominal current of the engine 40A);
- the size of the nominal current can change if necessary (the engineer of the PNR must be able to change the "necessary" current);
- manually switch to automatic mode;
- and in the automatic mode, the frequency of the engine should slowly decrease (0.5 Hz/min) until the current of the engine reaches: 2 A less than the "need" current.
The frequency of the engine turns should slowly decrease (0.2 Hz/min) until the current of the engine reaches the specified current.
- in the event of achieving the given current, it must be
- in the event of unforeseeable situation - when the current of the engine increases more than 41 A, the current frequency should increase rapidly (0,5 Hz / s) (to avoid the overload of the press engine) until the current of the engine reaches 35 A;
- after balancing the current of the engine to 35 A, we restore the work slowly reducing the frequency of turns of the engine to the specified nominal current;
- emergency situations on the current of the engine from the frequency converter and the heat relay of the electric-motor must be provided;
The accident must be accompanied by the corresponding message on the display of the programmed relay;
- the transition from the automatic mode to the manual must be carried out by the manual switch; the frequency on the PC must be left as in the automatic mode (more regulated by the manual);
- Frequency control range in automatic mode 30 - 60 Hz.Frequency converters that can be used in the scheme: ESV223N04TXB (22kW) "Lenze"; NZ2400-22G/30P Yilmaz
The product:
1) Program or consistency of logical functions for PR programming (programmed relay).2) Electric scheme principle: closets with PR (controller)
3) Developed instructions for PR programming with support contacts for the programming of the 1st study sample.
ТЕХНІЧНЕ ЗАВДАННЯ:
1) КЕРУВАННЯ частотником ПЧ по протоколу rs 485 Modbus RTU з ПР, за визначеною логікою, 2 режими: ручний, автоматичний
2) програмоване реле на розсуд: OMRON, Lovato, Schneider Electric, Simens
3) ПЧ: Lenze ESV223N04TXB (22кВт), зараз Ylmaz NZ2400-22G/30P
Умова:
1) На базі існуючої схеми розробити схему на базі програмованого реле для реалізації керування частотою обертів двигуна 22 кВт від його струму (А).
2) Зв'язок з частотним перетворювачем реалізувати по протоколу Modbus (RS-485).
3) Схема повинна бути реалізована для двох режимів роботи: ручного та автоматичного.
4) Запуск олійного пресу відбувається за участю оператора а потім ручним перемикачем переводимо в автоматичний режим.
5) Робота в автоматичному режимі передбачає наступний алгоритм:
- критерієм необхідного навантаження двигуна приймаємо його номінальний струм (номінальний струм двигуна 40А);
- величина номінального струму може змінюватися при необхідності (інженер ПНР повинен мати змогу змінити «необхідний» струм);
- ручним перемикачем переводимо в автоматичний режим;
- а автоматичному режимі частота обертів двигуна повинна повільно зменшуватися (0,5 Гц / хв) до поки струм двигуна не досягне: на 2 А менше «необхідного» струму
- далі частота обертів двигуна повинна повільно зменшуватися (0,2 Гц / хв) до поки струм двигуна не досягне заданого струму;
- в разі досягнення заданого струму він повинен підтримуватися в постійному значенні (механічне навантаження на двигун буде мати циклічний характер та змінюватися в межах -10 … +5%);
- в разі непередбачуваної ситуації - при зростанні струму двигуна більше ніж 41 А частота струму повинна стрімко зростати (0,5 Гц / с) (з метою уникнути перевантаження електродвигуна преса) до поки струм двигуна не досягне 35 А;
- після вирівнювання струму двигуна до 35 А, відновлюємо роботу повільно зменшуючи частоту обертів двигуна до заданого номінального струму;
- повинні бути передбачені аварійні ситуації по струму двигуна від частотного перетворювача та тепловому реле електро-двигуна;
- аварія повинна супроводжуватися відповідним повідомленням на дисплеї програмованого реле;
- перехід з автоматичного режима у ручний має здійснюватися ручним перемикачем; Частота на ПЧ має залишитись як при автоматичному режимі (далі регулюватиметься вручну);
- діапазон частотного керування в автоматичному режимі 30 ... 60 Гц.
Частотні перетворювачі які можуть використовуватися в схемі: ESV223N04TXB (22кВт) "Lenze"; NZ2400-22G/30P Yilmaz
ПРОДУКТ:
1) Програма або послідовність логічних функцій для програмування ПР (програмоване реле).
2) Електрична схема принципова: шафи з ПР (контролером)
3) Розгорнуті вказівки для програмування ПР з контактами підтримки для програмування 1-го дослідного зразка.
Applications 1
-
186 Good day !
I can realize your task on Siemens LOGO! or Schneider Electric Zelio - to your judgment. I would recommend Siemens LOGO!
I'll make the shapes of the management cabin, and the shapes of the field equipment connection.
I can collect the control closet, come for installation and start-up works.
Добрий день!
Можу реалізувати вашу задачу на Siemens LOGO! або Schneider Electric Zelio - на ваш розсуд. Я би рекомендував все ж таки Siemens LOGO!.
Зроблю схеми шафи управління, та схеми підключення польового обладнання.
Можу зібрати шафу керування, приїхати для монтажу та пусконалагоджувальних робіт.
Current freelance projects in the category Application programming
Bot for monitoring and booking tickets
201 USD
Hello. You need to write a program/bot that will automatically catch tickets (when they become available) and reserve them (simply by pressing 1 button). The challenge is that tickets appear approximately every 30 minutes, and you also need to be able to reserve them among… Application programming, Bot development ∙ 2 proposals |
Technology for creating software products IDLE ShellTask 1 Fill randomly with numbers from the range (b, c] and output the array B = (b1, b2, . . . , bn). Form the array A = (a1, a2, . . . , an) as follows: a1 = b1 sin 1, a2 = b1 sin 1 − b2 cos2 3, a3 = b1 sin 1 − b2 cos2 3 + b3 sin3 5, Output all elements of array A that are… Application programming, System programming |
Optimizing website loading / Google PageSpeed
28 USD
Optimize website loading speed to green zone on all Google PageSpeed metrics for desktop and mobile versions. Web programming, Application programming ∙ 16 proposals |
Automatic dialing program
200 USD
It is necessary to write a program for calling employees of the company. There is an Asterisk server, SIP account, the administrator has allocated 5 lines. The database is stored locally. The operator should form the call database: 1. Full name 2. Position 3. Phone number 4.… IP-telephony and VoIP, Application programming ∙ 1 proposal |
Import products to Simpla website and update themHello, you need to import products through data export. There are different export formats - csv, xml, xls. Also, it is necessary to update the availability of products from a Google spreadsheet. It is required that products with the same SKU from different sources (currently… Web programming, Application programming ∙ 3 proposals |