Development of the Air Conditioning Control Module
3 USDThe work logic is simple: the air conditioner has turned into cooling, cooled the room to +17 degrees after which the working mode immediately switch to heating and heats the room to +30 degrees. After achieving 30 degrees, the air conditioner immediately switchs to cooling and so cyclically. Now this is done by a person who works directly in this room, but there has been the ability to automatize this moment. I suppose you need either to develop a cast control block located inside the air conditioner, or to replace / ask the controller in the home block (if possible).Territorially the object is located in Dnepr, the cost is discussed
Необходимо разработать модуль управления кондиционером. Кондиционер обычный, бытовой. Работает на холод и на тепло, установлен в мини цеху по производству морепродуктов для поддержания требуемых показателей температуры и влажности в помещении.
Логика работы простая : кондиционер включился на охлаждение, охладил комнату до +17 градусов после чего сразу же режим работы переключается на обогрев и нагревает помещение до +30 градусов. После достижения 30-ти градусов кондиционер сразу же переключается на охлаждение и так циклически. Сейчас этим занимается человек, работающий непосредственно в этом помещении, но появилась надобность в автоматизации этого момента. Предполагаю, что нужно либо разработать кастомный блок управления, находящийся внутри кондиционера, либо заменить/прошить контроллер в родном блоке (если это возможно).Территориально объект находится в Днепре, стоимость обсуждаема
Client's feedback on cooperation with Oleksandr Mymrikov
Development of the Air Conditioning Control ModuleA competent and responsible executor.
He asked a lot of different questions about the project, which eventually get the most accurate TZ.
The work was performed a week before the agreed deadline. All the work was done remotely, after it was completed, I received a video report on the work of the device, which was then sent to me to the city by new mail.
During the course of the work Alexander himself decided all issues on the purchase of components etc.
I highly recommend this executive as an electronist, a programmer.
Freelancer's feedback on cooperation with Olga Olga
Development of the Air Conditioning Control Modulean adequate customer (who are not many here), not from the series "I want to get the EBU for the Boeing 737 engine on atmega8 and two LEDs for 10 backs and a half hour of time."
Answer questions quickly (commoned in Wiber). without any problems she sent a prepaid before the start of the work, and then watching the video report on the work of the device she sent the remainder.
-
1245 18 1 I will do everything as I agreed.
a universal iq command receiver capable of accepting a command of any protocol, saved it, and then reproduced by any event.
Also in the module will be implemented a thermostat with the output sensor and the input (buttons) and output (display) devices.
сделаю все, как и договорились.
универсальный приемник ик команд, способный принять команду любого протокола, сохранить ее, затем воспроизвести по какому либо событию.
также в модуле будет реализован термостат с выносным датчиком и устройствами ввода (кнопками) и вывода (дисплеем)
-
Добрый день.
Напишите, пожалуйста, модель Вашего кондиционера.
-
Ольга, я думаю, смогу это вам сделать. Но сначала желательно разобраться с вашим кондиционером и с гонораром мастеру, поскольку я не смогу это сделать за два - три дня.
-
здравствуйте
скажите:
1)весь стоковый функционал кондиционера Вас устраивает и нужно реализовать только авто переключение режимов и температур?
2)человек, выполняющий данную работу сейчас что конкретно выполняет, просто тыкает кнопки на пульте переключая режим/температуру?
-
Я между прочим серьёзно. Угадать интерактивную команду не получится. Типа, выташить, подождать пока погаснет, вставить и нажимать до тех пор пока там что-то не засветится. Гарантий никаких.
-
Сложность разработки - это отсутствие данного кондиционера в распоряжении разработчика. В частности думаю достаточно наличия пульта управления. В остальном - это блок ардуино, датчик и блок ик управления.
Покупка сплит системы на месте - 15000 руб. , разработка + коплектующие контроллера 3000 руб.
-
Current freelance projects in the category Embedded systems and microcontrollers
CRM with separate Prom functionality - HabberHello. There is a need for the following "crm". For example - I have 10 sites on prom.ua It is necessary that all orders from these sites are transferred to Hubber. I see it like this: all orders from 10+ sites are loaded into 1 crm - then transferred to Hubber via api.… Embedded systems and microcontrollers, Data parsing ∙ 2 proposals |
IOT Device
204 USD
It is necessary to develop a device that will collect sensor data every minute and write it to an SD card. Every 10 minutes, it will connect to WIFI and send the data via HTTP POST to the url [to be provided later] in JSON format with a specific token in the header. Upon… Embedded systems and microcontrollers, Web programming ∙ 2 proposals |
Programmer Arduino, LGT8F328p
306 USD
A reader of Mifare cards is needed LGT8F328p+rc522+ display Reading full dump, uid and all sectors. Display information on the screen, and via UART in the terminal. Library attached. Embedded systems and microcontrollers |
View the microcontroller menu.Good day ! We are looking for a programming designer for a re-design interface controller of the packaging trailer (packing device for products). You need to replace the old menu column with the new one that the designer will develop. Up to 15 screens with different buttons I… Embedded systems and microcontrollers |
Development of broadband antennasDevelopment of broadband antennas Develop, manufacture an experimental sample, and measure the parameters of a broadband antenna in the range up to 500MHz (there are tasks for other ranges as well) Both compact antenna options and those more suitable for radiation up to 10W are… Embedded systems and microcontrollers |